Austin Ten Drivers Club

Welcome to the Austin Ten Drivers Club Forums!

You are not logged in.

Post a reply

Write your message and submit
Confirmation code

To prevent spam the board requires you to enter a confirmation code. If you can't read the image click here to refresh.

Options

Go back

Topic review (newest first)

David
Yesterday 23:46:39

I was also getting puffs of smoke from the breather under the clutch housing but only when the car was in the over run., The seal between the gearbox and clutch was perfect with no signs whatsoever of the leakage of oil. I am certain it came from the engine side of the flywheel. In spite of all this the clutch didn't start slipping until the road speed exceeded 35 mph. When the pistons were taken out all the rings just fell apart, not one was complete and they were all broken in small parts but amazingly the engine still ran - tough little blighters these Austin engines. Thanks for all your help and advice everyone.

8565_Michael_Love
2018-12-02 20:34:34

It was a bit gooey smile

594_Phil_Taylor
2018-12-02 16:46:40

I agree with Michael and disagree with Peter; the oil mist does not 'disappear' when the engine is hot or get 'thrown off', it coats and lubricates many parts of the internals - valve guides, tappets, skew gears for the oil pump and distributor etc. - and the clutch! From my experience, this can happen to relatively new engines as well as poorly ones.

David,
Make sure you use the heavier clutch springs that were designed and manufactured by the Club - not sure if they are still supplied?

Phil

813_Peter_Winney
2018-12-02 12:05:09

Looks like it self converted to a fluid flywheel!

8565_Michael_Love
2018-12-02 09:37:02

Peter,

My gear box seal was fine when I sorted mine, but the clutch plates were heavily contaminated, as was the whole of the inside of the bell housing. That said, my scoring was pretty bad to the point you could almost see a puff out of the hole at the bottom of the housing with the engine running so I guess it depends on the severity of the leakage of gases...

This photo shows how bad it was after removing the flywheel assy. Not surprising the plates were fouled..

32462842850_ba4642880b_k.jpgAustin 10 engine rebuild by Mike Love, on Flickr

813_Peter_Winney
2018-12-01 22:53:49

Oil leaks from the engine leak on to the back of the flywheel and get thrown off by centrifugal force and drip out of the hole in the bottom of the bell housing.  Oil on the clutch linings is almost always caused by leaks from the front of the gearbox.

691_Richard_Ridlington
2018-12-01 09:00:29

Hi David,

You are correct in arriving at the cause for oil reaching the clutch.

I had the same problem with my engine through wear in the bores and the rings sticking because the van was laid up for many years during WW2 and after and as far as I'm aware the previous purchasers did nothing to the van resulting in excessive oil consumption and a slipping clutch.

The use of SAE 30 oil is not the cause - this is the recommended grade for winter use  - SAE 40 for summer.

Follow the good advice of Mike's post and you should have a good result.

Regards,

Richard.

8565_Michael_Love
2018-12-01 07:53:27

Hi David,

Mine did exactly the same when I had a little end pinch bolt fail and the gudgeon pin scored the bore allowing pressure past the rings and out through the bell housing.

If all your mechanics are sorted including the felt seals when you reassemble, and you clean everything before reassembly the oil thrower will work fine.

I think later models have a breather,

If you join the club you will have access to lots of technical help through the past forum posts for issues like this

Good luck with it,

Mike

David
2018-12-01 06:22:46

Before the engine on my A10 failed completely with a broken piston it appears that increased pressure in the sump caused by the oil being pressurized by exhaust gas escaping though a broken ring forced oil through the oil thrower plate at the end of the crank shaft and into the clutch housing - unless someone would like to dispute my theory with another possible cause.

Having reached the stage of rebuilding the engine is there any way the seal caused by the oil thrower ring/ plate where the crankshaft passes through the engine casting may be improved so I can reduce the possibility of oil reaching the new clutch plate.

Incidentally I have never overfilled the engine oil or used anything other than a 30 SAE single grade oil which was another suggestion made for the presence of oil on the clutch plate.

Board footer

Powered by FluxBB